Code Alarm CA-670 Manual de usuario

CA 670 Installation InstructionsAvoid mounting components or routing wires nearhot surfacesAvoid mounting components or routing wires nearmoving parts

(+)(-)Positive Polarity Output(+)(-)Negative Polarity Output2. BASIC INSTALLATION - 22 PIN BASE HARNESSStarter Input (Key Side) (GREEN)Starter O

Negative Door Input (GREEN)Locate the vehicle’s dome light or door pin switch wire.Verification: This wire will register ground (NEG) when the door

2. 22 PIN BASE HARNESS CONTINUEDHood Pin Input (-) (GRAY)Install a Hood Pin Switch and connect to the GRAY wire. This connections is required for Rem

Parking Light Output (+/-) (WHITE)Locate the vehicle’s parking light wire at the vehicle light switch.Verification: This wire will register positive v

Song Bird Output (BROWN/WHITE) SB1 Accessory requiredThis wire controls the SB1 accessory (Not Included).Connect this wire to one of the WHITE/BLACK

Parking Brake Input (GRAY/BLACK)NOTE: The following connection is only required for Turbo Timer.Verification: This wire will register ground when the

3. 6 PIN REMOTE START HARNESSBattery Power 1 (12 AWG) (RED)Locate the vehicle battery wire(s) at the ignition switch.Verification: These wires will

Active Output (-) 500mA (BLUE/BLACK)The Active Output/Ignition 3 output wire provides a ground output when the remote start function is activatedand r

4. 4 PIN REMOTE START PULSED OUTPUTSFused +12 VoltBattery Source308787a8685BLACK/YELLOW PulseDuring Crank WireTo Vehicle's2nd Starter Wire

Channel 2 (-) 500mA(PINK/BLACK)This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories(i.e. Power W

ANTENNA /RECEIVERSAFETYCONTROLSWITCH34Lt BLUE/GREENBLUEUNLOCK SENSE INPUTTRUNK PIN INPUT(-)567891011121314151617181920BLUE/WHITEWHITE/BLUEGRAYGRAY/BLA

Negative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Output (BLUE/GRE

6. DOOR LOCKSNegative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Ou

Negative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Output (BLUE/GRE

6. DOOR LOCKSNegative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Ou

Negative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Output (BLUE/GRE

6. DOOR LOCKSNegative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Ou

7. ACC. CONNECTOR'S8. SYSTEM POWER-UP PROCEDURE2 Pin Transponder Control Output: (Yellow Connector)This output is intended to allow the contro

9. System Testing1. Follow each instruction below.2. Verify that the system operates as indicated under each instruction. Refer to the system owners

Press DISARM:1. Doors unlock.2. Factory alarm (if equipped) is turned off.3. Siren/horn sounds once/ parking lights flash once.4. Courtesy lights turn

10. Mounting the Module / Finishing the Installation1. Mount the module to a brace or wire harness under the dash. The module and harnesses must be cl

22 Pin Base HarnessCA 670 System Layout1TUPTUOTHGILEMODETIHW/KCALB2TUPNIMRALAUNAMDER/EULB.TL3TUPNIHCTIWSKCOLNUNEERG/EULB.TL4NIPKNURTEULB5REGGIRTTNATSN

2 Pin Transponder Port (YELLOW)6 Pin Remote Start Harness3 Pin Door Lock Harness1STLOV21+DER21YROSSECCAEGNARO32YROSSECCAETIHW/EGNARO42NOITINGIETIHW/KN

Programming OptionsRF ProgrammerThe RF Programmer allows you to customize the system to fit the individual needs of the consumer, usinga handheld devi

Selecting Programmable Features1. Press the POWER button to turn the system ON.2. Once powered up the MENU screen will be displayed.3. Use the UP &

CA 670- Programming GuideFeature Bank 0 - 3 Chirps Transmitter ProgrammingFeature Bank 1 - 4 Chirps RF Programmer Receive BankFeature Bank 2 - 5 Chirp

1. SETUP & PROGRAMMINGTransmitter Programming (3 Chirps)1. With the door open turn the ignition ON.2. Press and hold the valet/override button.

1. 4 PIN MAIN POWER HARNESSProgramming Tach RateThe unit will not operate unless tach is programmed or tachless option is turned ON. If an attempt i