Code Alarm F65 Manual de usuario descargar pdf

MXM/TM FAULT

CODES

Codes common to all MXM/TMs

Digital Instrument Cluster Codes (EIC)

Error Code 1 - Engine Oil Pressure Sender Short Or Open Circuit

Error Code 2 - Engine Oil Pressure Sender Short To +Ve Voltage

Error Code 3 - Fuel Tank Level Sender Short To Ground

Error Code 4 - Fuel Tank Level Sender Open Circuit Or Short To +Ve Voltage

Error Code 5 - Wheel Speed Sender Short Circuit

Error Code 6 - Wheel Speed Sender Open Circuit

Error Code 7 - Coolant Temperature Sender Short Circuit

Error Code 8 - EDC Serial Link Failure. Communications Error

Error Code 9 - Transmission Serial Link Failure. Communications Error

Error Code 10 - Memory Retention Error Of Battery Calibration Constant

Error Code 11 -Memory Retention Error Of Operator Setting For Slip Alarm, Slip Zero

Reference Constant, Implement Width And Service Hours

Error Code 12 -Coolant Temperature Sender Open Circuit Or Shorted To A + Ve Voltage

Error Code 13 - Engine Shut Down Output Short To A +Ve Voltage

Instrument Cluster Inoperative

Electronic Hitch Codes (CFPS or GCM1)

Error code HL - Height limit incorrectly set to perform auto calibration

Error Code 2 - Poor Or No Signal From Tractor Performance Monitor Radar

Error Code 3 - Radar (Ground Speed) Greater Than Wheel Speed

Error Code 4 - Wheel Speed Greater Than Maximum Speed Of Tractor

Error Code 5 - Wheel Speed Zero When Radar Is Indicating Ground Speed

Error Code 6 - Slip Control Voltage Low (Short Or Open Circuit)

Error Code 7 - Slip Control Voltage High (Damaged Potentiometer Or Short To +12

Volts)

Error Code 8 - Raise/Work Switch Failure

Error Code 9 - Both External Lift/Lower Fender Switches Are Being Operated

Simultaneously

Error Code 10 - Height Limit Control Voltage Low (Short Or Open Circuit)

Error Code 11 - Height Limit Control Voltage High (Damaged Potentiometer Or Short

To +12 Volts)

Error Code 12 - Drop Rate Control Voltage Low (Short Or Open Circuit)

Error Code 13 - Drop Rate Control Voltage High (Damaged Potentiometer Or Short To

+12 Volts)

Error Code 14 -Open Circuit Connection To Load Sensing Pin, Short Circuit To Ground

Or Failed Load Sensing Pin

Error Code 15 -Load Sensing Pin Short Circuit To +12 Volts, Failed Or Corroded Load

Sensing Pin

Error Code 16 -Open Circuit Connection To Load Sensing Pin, Short Circuit To Ground

Or Failed Load Sensing Pin

Error Code 17 -Load Sensing Pin Short Circuit To +12 Volts, Failed Or Corroded Load

Sensing Pin

1 2 3 4 5 6 ... 18 19

Indice de contenidos

Pagina 1

MXM/TM FAULT CODES Codes common to all MXM/TMs Digital Instrument Cluster Codes (EIC) Error Code 1 - Engine Oil Pressure Sender Short Or Open Circuit

Pagina 2

Error Code U19 - Oil Temperature Below 10 Degrees Centigrade Error Code U21 - Engine RPM Too Low Error Code U22 - Engine RPM Too High Error Code U23 -

Pagina 3

Error Code F52 - Temperature Sender Short To Ground Error Code F53 - +5 Volt Reference Voltage Too High Error Code F54 - +5 Volt Reference Voltage Too

Pagina 4

Error Code FA5 - Creeper Solenoid Open Circuit Or Short To Ground Error Code FAA - Clutch A Solenoid Open Circuit Or Short To Ground Error Code FAB- C

Pagina 5

Error Code P22 - 4wd Solenoid Stuck On Error Code P23 - 4wd Output Open Circuit Error Code P24 - 4wd Driver Over Temperature Error Code P27 - PTO Spee

Pagina 6

Error Code R26 - EHR Control Unit 2 Full Flow Switch Error Error Code R27 -No Communication Between The EHR Valve 2 And The Central Controller (XCM) E

Pagina 7

Error Code 25 - Open centre position not reached, Valve internal fault, possibly mechanical Error Code 26 - Manual operation detected, Valve has been

Pagina 8

Error Code T20 -After-Run Not Completed, Data Valid But Below Normal Range Error Code T21 -After-Run Not Completed, Data Valid But Above Normal Range

Pagina 9

Error Code T4E-Coolant Temperature Sensor (PHY), Data Valid But Above Normal Range Error Code T4F -Coolant Temperature Sensor (PHY), Data Incorrect Er

Pagina 10

Error Code T96 - Monitoring Module, Data Valid But Below Normal Range Error Code T97 - Monitoring Module, Data Valid But Above Normal Range Error Code

Pagina 11

Error Code TE1 - Transmission oil plausibility error (transmission oil temperature signal out of limits) Error Code TE2 - Fan rpm out of range Error C

Pagina 12

Error Code 18 - Both Load Sensing Pins Disconnected Error Code 19 -Pin Reference Voltage Less Than 8 Volts (Short Or Open Circuit) Error Code 20 -Pin

Pagina 13

NOTE: If P34 and P40 appear, see Knowledge for keywords “Error codes P34 and P40 display” and follow the resolution. Error Code P01 - Rear PTO Brake S

Pagina 14

Error Code 4 - Fan speed out of range. Error Code 5 - Maximum fan speed low (maximum fan speed demanded but not achieved). Error Code 6 - +5V referenc

Pagina 15

Error Code U89 - Low/High Range Synchronizer Calibration Values Out Of Tolerance Transmission Codes (GCM2 or TCM) (Semi Powershift) Error Code CP - De

Pagina 16

Error Code F45 - Low/High Range Synchronizer Potentiometer Out Of Calibrated Range Error Code F47 - Clutch Disconnect Switch Misadjusted High Error Co

Pagina 17

Error Code U03 -Front Axle Potentiometer Short Circuit Auto Calibration Procedure Will Not Work Error Code U04 -Front Axle Potentiometer Threshold Is

Pagina 18

Error Code F59 -Forward/Neutral/Reverse Switch Disagreement (More Than One Switch Is Engaged) Error Code F60 - Upshift Switch Input Voltage Low Error

Pagina 19

Error Code FB4 - Reverse Clutch Solenoid Over Voltage Error Code FBA - Clutch A Solenoid Over Voltage Error Code FBB - Clutch B Solenoid Over Voltage